Yes, and it is one of the top 3 reasons people call us about appliances. The machine works perfectly, there is nothing wrong with it, and it is the wrong colour for the kitchen it now stands in. Almond, cream, brown and older shades of grey are the usual suspects, and they are usually the only thing in the room that gives its age away.
Refinishing changes the outer surface, so the colour changes without the appliance going anywhere.
Why does one appliance in the wrong colour matter so much?
Because kitchens read as a set. When 3 things match and 1 does not, the eye goes straight to the one that does not. It happens most often after a partial update: new units, new worktop, and a perfectly good fridge or cooker left over from before that now looks like a leftover. Refinishing brings it into line with everything around it.
It is a small change that fixes a disproportionate amount.
What colours can be matched?
Clean whites and light neutrals are the most requested by a wide margin, because that is what most updated kitchens are built around. We talk it through against your actual cabinetry and worktop rather than a colour card, since kitchen lighting changes how a finish reads. If you are refinishing more than one thing in the room, matching them to each other matters more than matching a swatch.
Can more than one appliance be done at once?
Yes, and it usually makes better sense than doing them separately. Where a kitchen has a fridge and a cooker, or a washer and dryer pair, from the same era, taking them all to 1 finish in a single visit is what makes the room look updated rather than partly updated. Tile in the same room can be included too, which is covered under tile refinishing.
Does a colour change affect how the appliance works?
No, because nothing inside it is touched. Refinishing deals with the outer surface only. We do not open the machine, we do not work on the mechanics, and if an appliance is not working properly then refinishing is not the answer to that. It needs to be sound and running before we put a new surface on it.
What about handles, seals and trim?
Those are masked and worked around rather than coated, which is what keeps the result looking like a finished appliance rather than something that has been painted in place. It is also the part that takes the time. A neat edge along a door seal is the difference between a job that reads as professional and one that does not, and it is worth asking about when you compare quotes.
How close a match can you get to the other appliances?
Close enough that the kitchen reads as a set, which is the point. Exactly matching a specific manufacturer's white is harder than people assume, because whites vary between makers and change as an appliance ages.
Where several pieces are being done, matching them to each other is the more useful target.
That is why doing a pair or a set in one visit gives a better result than refinishing one item to match two others. We will tell you which of those two situations you are in when we see photographs of the room rather than of the appliance alone.
What about the surfaces you cannot see?
Sides that sit against a unit and backs that face a wall are normally left, because they are not on show and coating them adds cost for no visible benefit. Where an appliance stands free and its side is visible, that side is part of the job. Tell us how it sits in the room when you send photographs, since the same appliance in a run of units and standing on its own are two different quotes.
Does the finish affect anything you touch daily?
Only the surface itself, and it behaves like a good factory finish. Handles, seals and control panels are masked and left alone, so nothing you operate is coated. That is deliberate, because a coated seal is the fastest way to a result that peels within months.
It is also why the masking takes as long as it does on an appliance.
When you compare quotes, ask directly what happens to the handles and the door seal. The answer tells you how carefully the job will be done.
What should you do next?
Photograph the appliance and the kitchen around it, so we can see what it needs to match, and send them with a quote request. Read more about appliance refinishing, see a refinished fridge on our before and after page, or call (441) 236-8827.
Photograph the kitchen as well as the appliance. Matching a fridge to the units and the worktop around it is the actual job, and a close up of the door on its own does not tell us what it has to sit against.
Common questions
Can you change the colour of a fridge?
Refinishing changes the outer surface, so the colour changes without the appliance going anywhere.
Does refinishing affect how the appliance works?
Refinishing deals with the outer surface only. We do not open the machine, we do not work on the mechanics, and if an appliance is not working properly then refinishing is not the answer to that.

