There is 1 distinction that decides this, and everything else is detail: is the rust on the surface, or has it gone through the material? Surface corrosion on a basin that is otherwise sound is very repairable. Corrosion that has eaten through leaves nothing solid for a new finish to sit on, and at that point a repair is not the honest answer.
Telling them apart is easier than it sounds.
How do you tell which one you have?
Look at the back and underside of the basin as well as the visible face, and look at whether the rusted area is still firm. Surface rust sits as staining and roughness on an area that is still solid. Rust that has gone through tends to show as pitting that has become a hole, flaking that lifts away, or a patch that gives slightly. If you can see daylight or damp coming through, that is your answer.
Where does basin rust usually start?
The overflow opening and around the waste, for the same reason it starts there on a bath: those are the places with a hole through the surface and water passing regularly. After that, any chip where something has been knocked or a fitting has been tightened. The pattern is consistent enough that we usually ask for a photo of those areas specifically.
Bermuda's humidity and salt air do not help any of it.
What does a repair involve?
The corrosion is cut back and treated so the new finish goes over sound material rather than sealing the problem in behind it, then the surface is rebuilt and finished so the repair does not read as a patch. Coating over active rust is the thing that makes it come back, usually within months, and it is the most common reason we get called to somebody else's work. The approach is set out under rust repairs.
When is replacing the right call?
When the material has corroded through, when the basin is cracked, or when it is loose or failing at its fixings. We will say so from the photos rather than after starting work, because a new surface on a failing basin helps nobody. Where the basin is sound and simply looks bad, replacing it is usually solving a cosmetic problem with a plumbing job, which is a comparison we set out on our refinish or replace page.
Can the basin and the bath be done together?
Yes, and it is the usual request. Where a bathroom suite is the same age it tends to be in the same condition, and doing the pieces in one visit gets a consistent result instead of one restored fixture next to a tired one. Baths are covered under bathtub refinishing.
What is covered afterwards?
Repairs carry a 6 month written warranty and a full reglaze carries 1 year, set out in writing with your quote. You also get a straight answer about whether the fixture is worth the work, which is the part we would want before spending anything.
What about the taps and the waste fittings?
They are masked and worked around rather than coated, which is what keeps the result looking like a restored basin rather than something painted in place. Fittings that are themselves corroded or failing are a separate question and not one we take on, since that is plumbing rather than surface work.
It is worth mentioning them when you send photographs.
A basin refinished beautifully with a badly corroded waste still looks wrong, and knowing about it up front means the two can be sequenced sensibly rather than one being done twice.
Is a pedestal or vanity basin different?
The surface work is the same. What differs is access and what else is in the way. A vanity basin set into a unit has edges and a seal around it that need careful masking, and a pedestal basin has an exposed underside and a column that are on show and usually worth including. Say which you have when you ask for the quote, and send a photograph that shows how it sits in the room rather than just the bowl.
Is a basin worth doing on its own?
Sometimes, and it depends what else is in the room. Where the bath and the tile are in good order and only the basin has gone, a single fixture is a sensible job. Where the whole suite is the same age and the same condition, doing the basin alone tends to make the bath look worse by comparison.
We will tell you which of those we think you have when we see the room.
What should you do next?
Photograph the rusted area close up, plus the whole basin and its underside if you can reach it, and send them with a quote request. SimPro has worked on Bermuda bathrooms since 2008. You can also call (441) 236-8827.
If you can reach the underside of the basin, photograph that too. Corrosion very often shows there before it shows on the face, and it is the clearest way to tell whether the material is still sound.
Common questions
Can rust on a basin be repaired?
Surface corrosion on a basin that is otherwise sound is very repairable. Corrosion that has eaten through leaves nothing solid for a new finish to sit on.
How do you tell if rust has gone through the material?
Rust that has gone through tends to show as pitting that has become a hole, flaking that lifts away, or a patch that gives slightly.

