Bathtub refinishing in Bermuda, without replacing the tub.

We refinish bathtubs where they stand and make them look new again. The tub stays in the room and the plumbing stays where it is.

A freshly refinished white bathtub in a bright Bermuda bathroom

Why refinish the tub you have

Most bathtubs that look worn are structurally fine. What has gone is the surface: the shine, the colour, a patch of rust at the drain, a chip from something dropped. Refinishing restores that surface on the tub you already have.

Because nothing is taken out, the tiles around the tub are not disturbed and there is no plumbing to redo. It is a cost effective alternative to replacement, and nothing goes to the tip.

  • Cast iron, steel and acrylic tubs
  • Staining, dullness and worn anti slip bases
  • Chips and rust treated as part of the job
A refinished white bathtub in a tiled alcove

Signs your tub is ready for a refinish

If any of these sound familiar, send us a photo.

Staining that will not clean off

Yellowing or marks that no amount of scrubbing shifts.

A dull, rough surface

The finish has worn thin and no longer feels smooth.

Chips on the rim or base

Small damage that will spread if it is left.

Rust at the drain or overflow

Orange marks creeping out from the metal fittings.

A colour you have outgrown

An older colour you would rather see in white.

A rental between tenants

A tired tub is the first thing a new tenant notices.

The same tub. Nothing replaced.

SimPro's own work in a Bermuda home. Drag the handle to compare.

Bathtub with rust and heavy staining around the drain before refinishingThe same bathtub after refinishingBeforeAfter

Bathtub, rust at the drain

Staining and rust around the waste, and a worn anti slip base. The tub stayed exactly where it was.

A cast iron roll top bath with dull, yellowed enamel and rust stainingThe same style of bath with a deep, even, freshly refinished white surfaceBeforeAfter

Roll top bath, dull enamel

An example of the kind of change a full reglaze makes to a tired roll top bath.

Drag the handle, or use the arrow keys, to move the line.

How a bathtub refinish works

One visit, carried out in your bathroom.

  1. Protect the room

    We mask the tiles, fittings and floor around the tub.

  2. Prepare the surface

    We clean, repair chips and rust, and prepare the old finish so the new one bonds.

  3. Apply the new finish

    The new finish goes on in even coats for a fresh, clean result.

  4. Cure and hand over

    We remove the masking, leave the room clean and explain how to care for it.

A technician applying a smooth white finish to a bathtub in a fully masked bathroom

A finish you can see and feel

A full reglaze gives the whole tub a fresh, even surface. Chips and rust spots are repaired first, so the new finish is smooth right across the tub rather than hiding damage underneath.

Afterwards it needs the same care as any good finish: a non abrasive cleaner and a soft cloth.

  • Full reglaze carries a 1 year written warranty
  • Chip and rust repairs carry 6 months
  • Tub liners carry 5 years
Request a free quote
The smooth glossy white rim of a refinished bathtub

Covered in writing

The warranty that applies is set out with your quote.

1 yearon a full bathtub reglaze
6 monthson repairs, including chip and rust repairs
5 yearson tub liners

What each warranty covers is set out in writing with your quote.

Questions about bathtub refinishing

If yours is not here, call and ask.

(441) 236-8827
Do you replace bathtubs?

No. SimPro refinishes the surface of the bathtub you already have. We do not take tubs out or carry out plumbing work.

What kinds of bathtub can you refinish?

Cast iron, steel and acrylic tubs, including roll top baths. Send a photo and we will confirm.

Can you fix a chip or rust as part of the refinish?

Yes. Chips and rust spots are repaired before the new finish goes on.

Is the work covered by a warranty?

Yes. A full bathtub reglaze carries a 1 year warranty, repairs carry 6 months and tub liners carry 5 years. What each covers is set out in writing with your quote.

How do I look after the new finish?

Use a non abrasive cleaner and a soft cloth, and avoid scouring pads and harsh powders. We go through it with you before we leave.

How do I get a price?

Send photos of the surface with the quote form, or call (441) 236-8827. Quotes are free and there is no obligation to book.

Send a photo. Get a price.

Tell us what the surface is and where you are on the island. We will come back with a quote for that job, free of charge.

Prefer to talk it through? (441) 236-8827
  1. We read the photosand work out what the surface needs.
  2. You get a pricefor that job, in writing, at no charge.
  3. We book a daythat suits the property, and we come to you.

Request a free quote

Photos help us price it accurately. You can attach more than one.

Monday to Friday, 8:00 AM to 5:00 PM. Saturday by appointment. See our Privacy Policy.

Call Request a Quote